|
Suction manifold
| D (mm) | D1 (mm) | L (mm) | L1 (mm) | n
| | 133 | 40,7 | 5030 | 1000 | 4
|
A section of the suction manifold to connect wellpoints with a pump unit
and providing a vacuum collecting pipeline for all takes.
|
| |
|
Elastic wellpoint 32
|
The wellpoint is made of elastic, semitransparent polyethylene tube with a filter protected by a mesh at its end.
|
| D (mm) | L (mm) | L1 (mm)
| | 32 | 7000 | 300
|
|
|
| |
|
Passage tube 133
|
The passage tube serves to extend the suction manifold of the wellpoint installation or to fill in a gap where there are no wellpoints installed.
|
| Symbol | D (mm) | L (mm)
| | 133/5000 | 133 | 5000
|
|
|
| |
|
Elastic connector 133
|
This connector is destined to connect the suction manifold of the wellpoint installation with the pump unit or to effect any change of direction in which the suction and dump collector is laid.
|
|
|
| |
|
External stopper 133
|
A stopper to plug the end of the suction manifold.
It can be also used to plug the suction stub pipe of the pump unit
(equipped with a stub tube or a distributor) during a trial run of its output.
|
|
|
| |
|
130/90 bend
|
To change the direction of laid suction manifolds.
|
|
|
| |
|
Rinsing hose
|
The rinsing hose is made of "Bezalin" and is used to connect the rinsing tube with the rinsing pump.
|
| Symbol | D (mm) | D1(mm) | L (mm)
| | 75/8000 | 133 | 75 | 8000
| | 51/8000 | 51 | 52 | 8000
|
|
|
| |
|
Rinsing tube 133
|
The rinsing tube is made of a 133 mm tube with a fitting and grip for extraction at one end and serrated dents on the other end. It is used to set wellpoints in the ground when bedding is required.
|
| Symbol | D (mm) | D1(mm) | L (mm)
| | 133/4500 | 133 | 4500 | 600
| | 133/6000 | 133 | 6000 | 600
|
|
|
| |
|
Rinsing tube 51
|
Made of a 51 mm tube with an internal fitting at one end. It is used to set the wellpoint in the ground without bedding it.
|
| Symbol | D (mm) | L (mm)
| | 50/6000 | 51 | 6000
|
|
|
| |
|
Flanged distributor
|
It has a flange like a stub tube at one end and two inlets equipped with 133 mm internal fittings at the other end.
|
| D (mm) | D1 (mm) | D2 (mm) | L (mm) | L1 (mm) | L2 (mm)
| | 133 | 160 | 14 | 310 | 365 | 20
|
|
|
| |
|
Flanged stub tube
|
The stub tube is used to quickly connect a pump unit with a suction manifold of a wellpoint installation and a dump collector.
|
| D (mm) | D1 (mm) | D2 (mm) | L (mm) | L1 (mm)
| | 133 | 160 | 14 | 165 | 20
|
|
|
| |
|
Wellpoint gasket
|
The gasket is shaped like an O-ring. It seals the connection of a wellpoint with a stub tube of a suction manifold.
|
|
|
| |
|
Gaskets
|
Gasket of the 51 mm
rinsing hose.
|
Gasket of the 133 D suction manifold.
|
|
| |
|
Plug
|
The plug is used to plug stub tubes of a suction manifold in case when there is no wellpoint at a given place, or in case, when due to a failure, a wellpoint is out of operation.
|
| D (mm) | D1 (mm) | L (mm)
| | 40 | 48 | 40
|
|
|
